set security ipsec vpn vpn-4f6b755d-1 ike gateway gw-vpn-4f6b755d-1 set security ipsec vpn vpn-4f6b755d-1 ike ipsec-policy ipsec-pol-vpn-4f6b755d-1 set security ipsec vpn vpn-4f6b755d-1 df-bit clear # This option enables IPSec Dead Peer Detection, which causes periodic # messages to be sent to ensure a Security Association remains operational. #

I already tried removing and adding VPN configuration step-by-step from both ends, nothing works, situation remains the same =(I can't even ping virtual interfaces IP addresses, which is. 10.1.59.1/30 - EdgeRouter vti0 interface. 10.1.59.2/30 - Juniper st0 interface. VPN state on Juniper: Juniper SRX SG VPN Security Technical Implementation Guide The Juniper SRX Services Gateway VPN must implement a FIPS-140-2 validated Diffie-Hellman (DH) group. Use of an approved DH algorithm ensures the Internet Key Exchange (IKE) (phase 1) proposal uses FIPS-validated key management techniques and processes in the production, storage, and control of MX960,MX480,MX240,MX104,MX80,MX40,MX10,MX5. Group VPNv2 Technology Overview, Understanding Group VPNv2, Group VPNv2 and Standard IPsec VPN, Understanding the GDOI Protocol, GDOI Protocol and Group VPNv2, Group VPNv2 Traffic, Group Security Association, Group Controller/Key Server, Group Member, Anti-Replay Protection for Group VPNv2 Traffic, Partial Fail-Open on MX Series Member Routers, Group MX960,MX480,MX240,MX80,MX40,MX10,MX5. Group VPN Technology Overview, Understanding Group VPN, Group VPN and Standard IPsec VPN, Understanding the GDOI Protocol, GDOI Protocol and Group VPN, Group VPN Traffic, Group Security Association, Group Controller/Key Server, Group Member, Group VPN Implementation Overview, Enabling Group VPN, Configuring the Service Set, Applying the Service Set, Packet And as indicated by the others who have responded, this is an explanation from the Juniper docs: " The group members use the Encapsulating Security Payload (ESP) protocol in tunnel mode to secure the traffic. However, in Group VPN the tunnel mode is modified.

From the AutoKey IKE VPN dialog box, in the left pane, expand Branch-Device1, and then click to select VPN Group. In the right pane, click to select the VPN group, and then click the Edit button. From the 1-VPN Group dialog box, edit the details as required. Click OK. Click Save.

Howto Juniper SSG - Shrew Soft Inc

The configuration template provided is for a Juniper SRX router running JunOS 11.0 software (or later). # Defining the IKE Proposal for Oracle # This IKE (Phase 1) configuration template uses AES256, SHA384, Diffie-Hellman Group 5, and 28800 second (8 hours) IKE session key lifetime. set security ipsec vpn oracle-vpn-

Configure Dynamic VPN Users and IP Address Pool. set access profile Dynamic-XAuth client Jed … Howto Juniper SSG - Shrew Soft Inc The Shrew Soft VPN Client has been tested with Juniper products to ensure interoperability. Overview. The configuration example described below will allow an IPsec VPN client to communicate with a single remote private network. The client uses the push configuration method to acquire the following parameters automatically from the gateway. IP Troubleshooting Juniper-Cisco Layer3 VPN Hi Folks, I am trying to simulate Layer3 VPN between Juniper J2320 and Cisco 2611. However it seems that Juniper router is not sending VPN routes to Cisco router. I have verified the LDP, BGP and OSPF they are all operational. The attached document has got the configuration of Juniper and Cisco [SRX] Example - How to configure a dialup IPSec VPN with